Wednesday, February 27, 2019
Ball bounce higher when it is warmed up Essay
Prediction I predict that for this look into the higher the temperature, the much the bollock willing bounce. I put this down to the temperature is raised, the particles inside will gain energy hence the higher the bullock block will bounce. Equipment For this experimentation I will habit the following equipment to do this experiment 1. Beaker 2. Bunsen burner 3. Splints 4. Tripod 5. Gauze 6. Thermometer 7. Squash stumblebum 8. Paper Towels 9. Meter Ruler 10. Tongs 11. Stop Clock 12. refuge goggles. Method Choose whizz yellow spot squash ball.This will be used through bring come to the fore the experiment to ensure that the ball is do of the same rubber and same size. The experiment will be carried out on the hard floor tiles of the science laboratory. The area will be clean to ensure there are no irregularities on the surface. The ball will be heated to the required temperature by placing it in a beaker of heated water for one minute. To ensure the human being body do es non affect the temperature, tongs will handle it. temp (? C) Temp (Kelvin).Results I am going to work out pressure and predicted light succession using the following faces. This is how to work out pressure P1 is Pressure 1, which is forever 1. T1 is Time 1 and T2 is Time 2. This number changes as you work out To work out predicted hang conviction you use this formula. In this formula P1, P2 etc are Predicted hang condemnation. This number changes as you work out Temp (Kelvin) Pressure Predicted Hang time Actual Hang time.Analysis From my represent I can see that the predicted hang time and the actual hang time differ greatly from 293 Kelvin onwards, the real hang time increases quite dramatically where as the predicted hang time escalates only a bit. From doing this experiment I have found out that when pressure is change magnitude by raising the temperature inside a squash ball, the particles gain more energy and can reform more quickly from its bear on on the surface .My actual hang time results show this. My prediction was correct in the sense that my theory of the particles gaining energy worked. My predicted hang times unfortunately were not correct. They were not a good match to my actual hang time results I put this down to another variable. The other variable I intend is plasticity of the squash balls material. I believe that if the ball has high elasticity then the deformation (formed by the impact of the ball hitting the surface) of the ball will be larger and because it is bigger it will reform more quickly and bounce higher.The energy at the start of the dropping process gravitational potential energy, but as the ball speed increases this changes to kinetic energy. When the ball reaches impact, kinetic energy changes to elastic potential energy and a bit of thermic and sound energy. This thermal and sound energy remain at a low never-ending throughout the rest of the balls bounce back. When the ball reforms it bounces up and gravit ational energy increases to its previous level. Evaluation I think I conducted my experiment to a high standard and there were no major nonsensical results (except the hang time and predicted hang time results).Each result had an ordinary difference of 7. 9 between the next one, this average was brought down drastically by the 2. 8 difference between the first two results (38. 4 and 41. 2). If I were to make any improvements to the method and equipment of this experiment I would 1. convince the way the ball was dried as I think a more sophisticated way could be used to prevent human error. 2. Use a variant way of timing the balls impact to the state a touch sensitive timer mat would work well. 3.I would try different surfaces on which the ball lands on, this could be thought of as another variable I could dumbfound. If I were to do this experiment I would change the temperatures to smaller differences i. e. 273 Kelvin, 278 Kelvin etc. to see if I could recoup an ideal temper ature that had a good enough bounce to help develop work into elasticity of the balls material. If I were to develop this experiment further I would test elasticity. To test this I would experiment with a range of different squash balls.I would cut them into equal narrow pieces and use a Newton spring to test how much the piece of squash ball could hold and how long it would take to reform back to its original shape, for this I would use a Newton spring and stop clock. All in all I think I conducted myself well on this experiment and have learned a lot. Emma Dovaston 11GG Show preview only The above preview is unformatted text This student written piece of work is one of many that can be found in our GCSE Electricity and magnetic force section.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.